Jump to content

Uwe T.

  • Posts

  • Joined

  • Last visited


2 Neutral
  1. Uwe T.

    IONIQ 5

    Is there a way to make the video display smaller?
  2. Uwe T.

    IONIQ 5

    So here's the list of flipping values while charging: SOC DIsplay: real value <--> -0,5% SOC BMS: real value <--> -0,5% CEC (Cumulated Energy Charged): real value <--> -1684300,9kWh Battery Current: real value <--> 25,7A Battery Voltage: real value <--> 25,7V Energy Draw (calculated from BattCurr and BattVolt): real value <--> 0,7kW Battery Temperature: real value <--> -1,0°C At least those are the values I found in my car, don't know whether other cars would produce the same values Flipping_values[1].mp4
  3. Uwe T.

    IONIQ 5

    Some of the strange values can be seen in the video sequence I previously posted. They only show up while charging. At the time of that recording I was using a China OBD adaptor. But since it failed on re-connects I changed the adapter. Now I'm using Scantool OBDLink LX which works very reliably, so I would assume the cause is not noise on the CAN bus caused by the adapter. I will do another screen recording soon so you can see the values that appear. There's -25.7A or V resp. in BattCurrent and BattVoltage (resulting in a wrong Power Draw vallue since it's calculated from those two). Also SOC jumps to -0.5%, and CEC jumps to -1,6xx,xxx kWh (the minus cannot be seen in the above recording). BattTemp jumps to -1.0°C.
  4. Uwe T.

    IONIQ 5

    Thanks a lot! I am receiving data now. I'll have to check while driving whether I receive correct data. While charging I still have the problem with values that go back and forth between reasonable and definitely wrong values for all values that are being sent to http://api.iternio.com/1/tlm/torque - also for SOC and Batt Temp (must have missed that when writing my previous comment). I also see those values in ABRP now - also going back and forth while charging. As for calibration: I have set up two options for my IONIQ5: Standard, and towing a caravan. Will the data be evaluated seperately, e.g. for calibration of consumption? I'm asking, because we will travel some 300km towing a caravan soon and don't want this to mess up calibration.
  5. Uwe T.

    IONIQ 5

    I tried to feed live data from OBD adapter using Torque pro. I used the PID set for Kona&Niro, had the values that are supposed to be uploaded displayed in Torque pro, and the values seem to make sense - just while charging the seem to go back and forth between reasonable values - except SOC and Batt Temp - and values that don't make sense at all. I obtained a token for a generic link to live data in ABRP (beta) and used it as email address in Torque pro. However, I don't see any option in ABRP to switch to live data. Now I don't know at which point the procedure fails. Where can I find out whether the data is being uploaded? Do I have to do more than just set up Torque pro and obtain the token in ABRP to be allowed to upload data to http://api.iternio.com/1/tlm/torque? Screen_Recording_20210812-112848_Torque_1[1].mp4
  6. Actually I'd be interested in feeding live data from my IONIQ5 to ABRP. Tronity doesn't work, because it doesn't update data appropriately - seems to be a problem of the link between Bluelink and Tronity (also received the message that the maximum number of daily vehicle checks has been exceeded). It seems there used to be a guide, how to set up a connection to torque pro. However the link I found in an 2018 article is dead. Can you help? I used the PIDs for Hyundai Kona, and the values seemed to be correct (only checked SOC Display, SOC BMS, and Cumulated Energy Charged so far)
  7. I'm very happy ABRP has gone AA! I ran into 2 issues, though. 1. When using Android Auto place names are not rotated correctly. As a consequence, when driving southbound place names are displayed upside down. 2. When using Android Auto there is no way to show the detailed graph for elevation and estimated course of SoC on the car device (proposal: could be invoked with a click on the estimated SoC on arrival). The graph can be shown on the smartphone, but only at the first start after starting navigation. Later there seems to be no way to show the graph for the active navigation. I think, parts of my observation have been reported in posts by someone else. Best Uwe
  • Create New...